ISDU Indices

Access Rights: ro – Read Only, rw – Read/Write, wo – Write Only

System Command

Name	Index	Bytes	Access	Values	Description
System Command	2	1	wo	see Events & Commands

Identification

Name	Index	Bytes	Access	Values	Description
Vendor Name	16	23	ro	CAPTRON Electronic GmbH
Product Name	18		ro	CANEO series4x (Display)
Product ID	19	10	ro	Cx4xX-xxxx
Product Text	20	19	ro	Order-code
Symbol	276	3	ro
Hardware Identification Key	17342	9	ro
Serial Number	21		ro
Firmware Version	23		ro	V5.x
Function Tag	25	32	rw	***

Activation Parameters

Name	Index	Bytes	Access	Values	Description
Sensor Mode	261	1	rw	1 - Toggle, 2 - Dynamic, 3 - Static	Toggle: Touch to switch on, touch again to switch off. Can only be set back after "Output Minimum Impulse Time" is over. Dynamic: Output is on as long as "Output Minimum Impulse Time" is set; even though the user continues touching, the output will switch off. Static: Output is on until the user is no longer touching the sensor (but is at least on for the "Output Minimum Impulse Time").
Touch Sensitivity	260	1	rw	0 - High, 1 - Middle, 2 - Low	High: required "Actuation Strength" > 4%. Middle: required "Actuation Strength" > 14%. Low: required "Actuation Strength" > 24%.
Glass Thickness	292	1	rw	1 - glass below 4mm / plexiglass below 2mm, 2 - glass 4mm to 7mm / plexiglass 2mm to 3mm, 3 - glass 8mm to 10mm / plexiglass 4mm to 5mm	series44 Glass devices only.
Minimum Actuation Time	263	2	rw	0 ... 65535 [ms]	Time the sensor must be activated before output on Pin 4 switches, "Actuation Flag" is set to "Actuated" and "Actuation Count" goes up.
Minimum Actuation Time (Toggle OFF)	283	2	rw	0 ... 65535 [ms]	Time the sensor must be touched in "Toggle" mode before output on Pin 4 turns OFF and "Actuation Flag" is set to "Idle".
Output Activation Delay	324	2	rw	0 ... 65535 [ms]	Time the switching of the output is delayed when the sensor has been actuated.

I/O Parameters

Name	Index	Bytes	Access	Values	Description
Active Inputs	271	1	rw	3 - None (3 pin mode), 4 - Pin 2 (E1) (4 pin mode), 5 - Pin 2 (E1) and Pin 5 (E2) (5 pin mode)	Controls which input pins are monitored.
E1/E2 Mode	272	1	rw	0 - Active Low, 1 - Active High	Active Low: Accepts a low signal as input to turn on. Active High: Accepts a high signal as input to turn on.
Output Locking	337	1	rw	0 - No locking, 1 - Release by E1, 2 - Release by E2, 3 - Release by E1 and E2	Controls whether inputs E1/E2 must be active for the output signal on Pin4 to be ON when the sensor is touched.
Output Mode	273	1	rw	0 - NPN, 1 - PNP, 2 - PushPull	NPN: Output signal is pulled down to 0V when output is on. PNP: Output signal is pushed up to +VDC when output is on. PushPull: Output signal is pushed up to +VDC when output is on and is pulled down to 0V when it is off.
Output NO/NC	274	1	rw	0 - NO (Normally Open), 1 - NC (Normally Closed)
Output Minimum Impulse Time	275	4	rw	10 ... 86400000 [ms]	The minimal time (ms) of the output signal when the sensor is activated. The output signal cannot be interrupted. In toggle mode the sensor can only be deactivated after the minimal output signal length is over.

LED Parameters

Name	Index	Bytes	Access	Values	Description
LED Control Mode	293	1	rw	0 - Automatic Scene selection, 1 - Scene controlled by IO-Link Process Data, 2 - Advanced control by IO-Link Process Data	See LED & Display Control for details on each mode.
Adaptive LED Brightness	270	1	rw	0 - Off, 1 - On	If turned "On" the sensor automatically adjusts the LED Brightness depending on the "Surrounding Brightness".
Manual LED Brightness	305	1	rw	0 ... 100 [%]	Brightness of LED Ring and 7-Segment Display. Sets minimal brightness if "Adaptive LED Brightness" is turned "On".
Rotate Button	304	1	rw	0 - 0°, 1 - 180°	Rotate LED Display – use if button is mounted upside down.
Boot Sequence	314	2	rw	0 - Off, 1 - Classic, 2 - CANEO	Off: Immediately available. Classic: Countdown sequence. CANEO: CANEO sequence.

Custom Colors

Custom Color 1 (Index 306)

Subindex	Component	Values
1	R	0 ... 255
2	G	0 ... 255
3	B	0 ... 255

Custom Color 2 (Index 307)

Subindex	Component	Values
1	R	0 ... 255
2	G	0 ... 255
3	B	0 ... 255

Timer Parameters

Name	Index - Subindex	Bytes	Access	Values	Description
Timer Function	322 - 1	1	rw	0 - disabled, 1 - count down, 2 - count up, 3 - count up infinitely	Controls timer behavior.
Trigger Timer	322 - 2	1	rw	0...7 - when entering Scene n	Trigger to start timer. The timer starts when sensor enters/falls back into a certain scene.
Timer Timeout	322 - 3	2	rw	0 ... 9999 [s]	Time after which the timer stops.
LED Color	323 - 1	1	rw	0 - CANEO, 1 - Red, 2 - Green, 3 - Blue, 4 - Yellow, 5 - Magenta, 6 - Cyan, 10 - Orange, 11 - Violet, 13 - Off, 14 - Clean Blue, 128 - Custom Color 1, 129 - Custom Color 2	LED color during timer.
Timer LED Effect	323 - 2	1	rw	See LED Effects reference. Additionally: 24 - Timer Circle Clearing Clockwise, 25 - Timer Circle Clearing Counter-Clockwise, 26 - Timer Circle Filling Clockwise, 27 - Timer Circle Filling Counter-Clockwise	Effects 24–27 are synchronized with the timer.
Effect Frequency	323 - 3	1	rw	1...60, 0 - Default Frequency [0.1 Hz]	Frequency of LED effect in 1/10 Hz, range: 0.1 ... 6 Hz. Applies only for animated effects.

Observation & Diagnosis

Name	Index	Bytes	Access	Values	Description
Sensor Temperature	257	2	ro	-32768 ... 32767 [0.1 °C]
Supply Voltage	256	2	ro	0 ... 65535 [0.001 V]
Input E1 voltage	277	2	ro	0 ... 65535 [0.001 V]
Input E2 voltage	278	2	ro	0 ... 65535 [0.001 V]
MCU Voltage	279	2	ro	0 ... 65535 [0.001 V]
Charge Code	280	4	ro	0 ... 4294967295
Error Code	282	2	ro	0 ... 65535
Flash Erase Count	259	2	ro	0 ... 65535
Device Access Locks	12		rw